Parameters

Name	Description
Modem_t	Modem temperature
DIN4	Ignition(DIN4)
CANReqSupp	FMS parameter SPN 2805 0=request is not supported 1=request is supported 2=reserved 3=don´t care
CANDiagnosticSupp	FMS parameter SPN 2804 0=diagnostics is not supported 1=diagnostics is supported 2=reserved 3=don´t care
FMS	FMS parameter 0x00FDD1 software version in format ab.cd
CANVehicleMotion	FMS parameter SPN 1611 0=Vehicle motion not detected 1=vehicle motion detected 2=Error 3=Not available
CANDriverStatus	FMS parameter SPN 1617 0=normal 1=15 min bef. 4 ½ h 2=4 ½ h reached 3=15 min bef. 9 h 4=9 h reached 5=15 min bef. 16 h 6=16h reached 14=Error 15=not available
CDC1	FMS parameter SPN 1615 0=Card not present 1=Card present 2=Error 3=Not available
CDT2	FMS parameter SPN 1618 0=normal 1=15 min bef. 4 ½ h 2=4 ½ h reached 3=15 min bef. 9 h 4=9 h reached 5=15 min bef. 16 h 6=16h reached 14=Error 15=not available
CDC2	FMS parameter SPN 1616 0=Card not present 1=Card present 2=Error 3=Not available
fuel1	Fuel Counter 1
fuel2	Fuel Counter 2
fuel3	Voltage on analog input 3 pin
fuel4	Voltage on analog input 4 pin
IN1	Voltage on analog input 1 pin
IN2	Voltage on analog input 2 pin
Tacho_ddd	Tacho card reader state
SecInf	01-configuration change attempt, when plock enabled 02-plock code sending attempt failed 04-plock state succesfully updated
AIDelta1	Voltage difference between the current and earlier obtained voltage reference on AIN1
GSM	GSM/UMTS signal level
Prfl	Represents the currently active configuration profile
Vsourse	Power supply voltage
Vbattery	Battery Voltage
PCBT	Represents temperature of the PCB
AIDelta2	Voltage difference between the current and earlier obtained voltage reference on AIN2
iButID	Unique iButton ID
CANClutchSwitch	FMS parameter SPN 598 0=pedal released 1=pedal pressed 2=Error 3=Not available
CANBreakSwitch	FMS parameter SPN 597 0=pedal released, 1=pedal pressed, 2=Error, 3=Not available
CANCruiseSwitch	FMS parameter SPN 595 0=switched off 1=switched on 2-Error 3=Not available
CANPTO	FMS parameter SPN 976 (bin 00000) 0= off/disabled, (bin 00101) 5= Set, (bin 11111) 31 = not available
CEPLCS	FMS parameter SPN 92 Engine Percent Load At Current Speed, 1% / bit, 0 offset, 0 to 125 % op. range
CTL	FMS parameter SPN 928 Bit-mapped, low order 4 bits represent tire location counting left to right facing forward, 0=tire that is most to the left on a certain axle, ….., 15=Not available
CAW	FMS parameter SPN 582 Axle 1 weight from CAN (20000=10000kg)
CSE	FMS parameter SPN 1622 0=no tachogr. Event, 1=tachogr. Event, 2=Error, 3=Not available
CHI	FMS parameter SPN 1621 0=no handling information, 1=handling information, 2=Error, 3=Not available
CDI	FMS parameter SPN 1619 0=Forward, 1=Reverse, 2=Error, 3=Not available
DIN1h	DIN1 hour counter
AccX	Acceleration vector length relative to x axis
AccY	Acceleration vector length relative to y axis
AccZ	Acceleration vector length relative to z axis
AxleW2	FMS parameter SPN 582 Axle 2 weight from CAN (20000=10000kg)
DFuelC1T_dispd	Digital Fuel Sensor C1 temperature
DFuelC2T_disempt	Digital Fuel Sensor C2 temperature
DFuelC3T_engeff	Digital Fuel Sensor C3 temperature
DFuelC4T_chrgeng	Digital Fuel Sensor C4 temperature
DFuelC5T_plugin	Digital Fuel Sensor C5 temperature
DFuelC6T_fullchrg	Digital Fuel Sensor C6 temperature
DFuelC7T	Digital Fuel Sensor C7 temperature
DFuelC8T	Digital Fuel Sensor C8 temperature
DFuelC9T	Digital Fuel Sensor C9 temperature
Odom	Mileage calculated by the GNSS module
DFuelS1	Digital Fuel Sensor C1
DFuelS2	Digital Fuel Sensor B1
DFuelS3	Digital Fuel Sensor C2
DFuelS4	Digital Fuel Sensor C3
T0	Temperature sensor0 ID
T1	Temperature sensor1 ID
T2	Temperature sensor2 ID
T3	Temperature sensor3 ID
TS3	Temperature sensor3
DFuelC10T	Digital Fuel Sensor C10 temperature
DFuelB1T	Digital Fuel Sensor B1 temperature
OdoDelta	Virtual odometer DIFF
T00	Temperature sensor0
T01	Temperature sensor1
T02	Temperature sensor2
DFuelC4	Digital Fuel Sensor C4
DFuelC5	Digital Fuel Sensor C5
DFuelC6	Digital Fuel Sensor C6
DFuelC7	Digital Fuel Sensor C7
DFuelC8	Digital Fuel Sensor C8
DFuelC9	Digital Fuel Sensor C9
DFuelC10	Digital Fuel Sensor C10
GSM_jamming	GSM/UMTS jamming
CAIT	CAN ambient air temperature
CFE	CAN instantaneous fuel economy
CPTO	CAN at least one PTO engaged. FMS parameter SPN 3984 0=No PTO drive is engaged 1=At least one PTO drive is engaged 2=Error 3=Not available
CHRFC	CAN high resolution engine total fuel used
DTC_MIL	OBD DTC and MIL
RPM	OBD RPM
SpeedSensor	OBD vehicle speed
EngT	OBD engine coolant temperature
AirT	OBD ambient air temperature
FuelPr	OBD fuel level
FuelType	OBD fuel type
FuelRate	OBD engine fuel rate
EngPr	OBD actual engine percent torque
Distance	OBD distance traveled while MIL is activated
AccPP	OBD accelerator pedal position
VIN1	OBD VIN
VIN2	OBD VIN
VIN3	OBD VIN
EngTSt	OBD time since engine start
dtc_count	OBD DTC count
accident_din3	DOUT3 status
accident_din4	DOUT4 status
SDCardLog	SD card log. 0 – disabled, 1 – enabled, 2 – log write error
CD	CAN high resolution total vehicle distance
CCT	CAN engine coolant temperature
CFR	CAN fuel rate
CANTotalDrivingTime	TCO_CAN total driving time
CANCurrentActivityDuration	TCO_CAN current activity duration
CANContiniusDrivingTime	TCO_CAN continuous driving time
CANBreakTime	TCO_CAN break time
CANDriverTimeStates	TCO_CAN driver time states
CANFuelUsedDelta	CAN Fuel used delta
CV1	CAN vehicle ID
CFD1	CAN first driver ID
CFD2	CAN first driver ID
CSD1	CAN second driver ID
CSD2	CAN second driver ID
OT_temp_sensor_1	OT temperature sensor 1
Operator	Unique Mobile operator code
TCO1	TCO vehicle ID
TCO2	TCO vehicle ID
TCO3	TCO vehicle ID
TCOD1	TCO first driver ID
TCOD2	TCO first driver ID
TCOSD1	TCO second driver ID
TCOSD2	TCO second driver ID
TCOFDS	TCO first driver state
TCOCDS	TCO second driver state
TCOFDC	TCO first driver card
TCOSDC	TCO second driver card
TCOD	TCO distance
TCOT	TCO trip distance
TCOVS	TCO vehicle speed
TCORPM	TCO engine speed
TCORN1	TCO registration number
TCORN2	TCO registration number
ECO_idling_state	ECO idling event
battery	Battery charge current
RFIDA	RFID PortA
RFIDB	RFID PortB
MovementSensor	Movement sensor. 0=No motion detected 1=Motion detected
SleepTimer	0 – No event 1 – device wake-up by timer event
DFS	Fridge total electric hours
FridgeTotalVehHours	Fridge total vehicle hours
FridgeTotalEngHours	Fridge total engine hours
FridgeAlarmType	Fridge alarm type. 0 – No Alarm; 1 – Level 0 Alarm (Log-Stored / Routine Maintenance Required); 2 – Level 1 Alarm (Low Fuel); 3 – Level 2 Alarm (Maintenance Past Due); 4 – Level 3 Alarm (Reserved for Future Use); 5,6,7 – Level 4,5,6 Alarms (Reserved for Future Use); 8 – Level 7 Alarm (Check / Immediate Attention Required); 9,10,11,12,13,14 – Level 8,9,10,11,12,13 Alarms (Reserved for Future Use); 15 – Level 14 Alarm (Shutdown or Catastrophic System Failure)
FridgeAlarmCode	Fridge alarm code
FridgeReturnAir_t	Fridge return air temperature
FridgedischargeAir_t	Fridge discharge air temperature
FridgeSetpoint_t	Fridge temperature setpoint
FridgeEvaporatorCoil_t	Fridge evaporator coil temperature
FridgeOperatingMode	Fridge operating mode
FridgeCycleMode	Fridge cycle mode
FridgeHighSpeedStatus	Fridge high speed status
FridgeDoorStatus	Fridge door status
FridgeDiselElectStatus	Fridge diesel/electric status. 0 – Diesel mode (default); 1 – Electric mode
OTDI1	OT digital input 1
OTDI2	OT digital input 2
OTDI3	OT digital input 3
OTDI4	OT digital input 4
CRPM	CAN engine speed
ACCIDENT_harsh_acceleration	CAN AdBlue level
CAN_J1939_trailer_weight	CAN J1939 trailer weight
CEH	CAN engine hours
CSD	CAN service distance
CANFuel_level_liters	CAN Fuel level liters
CAPP	CAN accelerator pedal position 1
fuelLevel	CAN fuel level1
CFU	CAN engine total fuel used
CANEngine_fuel_level_secondary	CAN engine fuel level secondary
CANWheelBasedSpeed	CAN wheel based speed
DFuelA1	Digital Fuel Sensor A1
DFuelA1T	Digital Fuel Sensor A1 temperature
TachoSpeed	CAN tachograph vehicle speed
CANJ1939_cargo_weight	CAN J1939 cargo weight
TachoDriverWorkingState1	CAN tacho driver1 working state
TachoDriverWorkingState1	CAN tacho driver2 working state
TachoPerfomance	CAN tachograph performance
TachoVehOverSpeed	CAN tacho vehicle overspeed
AxleLocation	CANBUS Axle location
CAN_FuelLevel2	CAN Fuel level 2. FMS parameter SPN 38 125 = 50% Ratio of volume of fuel to the total volume of fuel container