Parameters

Name	Description
HardVersion	Hardware version
SoftVersion	Firmware version
IMEI	IMEI in ASCII
ID	Identifier of a device
NumberOfPacket	Number of an archive record
Height	Height, m
HDOP	One of the values: HDOP, if GLONASS/GPS module is coordinates source Error in meters, if cellular base stations are a source
StatusOfDevice	Status of device
Vsource	Supply voltage, mV
Vbattery	Battery voltage, mV
Temperature	Inside temperature, °C
OUT1, OUT2… OUTN	Status of outputs
DIN1, DIN2 … DINN	Status of imputs
AccX	acceleration by X axis
AccY	acceleration by Y axis
AccZ	acceleration by Z axis
IN0	Input voltage 0 Depending on settings: 1. voltage, mV, 2. number of pulses; 3. frequency,Hz.
IN1	Input voltage 1 Depending on settings: 1. voltage, mV, 2. number of pulses; 3. frequency,Hz.
IN2	Input voltage 2 Depending on settings: 1. voltage, mV, 2. number of pulses; 3. frequency,Hz.
IN3	Input voltage 3 Depending on settings: 1. voltage, mV, 2. number of pulses; 3. frequency,Hz.
Omnicomm000	RS232 0
Omnicomm001	RS232 1
Temperature0/1/2../7	Thermometer 1/2/../7 identifier and measured temperature, °C
iButton	First iButton key identification number
FMS_TF	CAN-bus and CAN-LOG data (CAN_A0). Fuel used by a vehicle from the date of manufacturing, l
FMS_AF	CAN-bus and CAN-LOG data (CAN_A1). Fuel level, %; coolant temperature, ⁰C; Enginespeed, rpm.
FMS_L	CAN-bus and CAN-LOG data (CAN_B0). Vehicle`s mileage, m.
FMS	CAN_B1
CAN8_0	CAN8BITR0 or vehicle speed from CAN-LOG, km/h
CAN8_1	CAN8BITR1 or the 2rd byte of prefix S CAN-LOG
iButton_ID	The second iButton key identification number
Mileage	Total mileage according to GPS/GLONASS units data, m
iButton_State	State of iButton keys, identifiers of which are set by iButton command
AIN0	Input 4 values. Depending on settings: 1. voltage, mV 2. number of pulses 3. frequency, Hz
AIN1	Input 5 values. Depending on settings: 1. voltage, mV 2. number of pulses 3. frequency, Hz
AIN2	Input 6 values. Depending on settings: 1. voltage, mV 2. number of pulses 3. frequency, Hz
AIN3	Input 7 values. Depending on settings: 1. voltage, mV 2. number of pulses 3. frequency, H
DS1923_0 /1/2…/7	Zero DS1923 sensor Identifier, measured temperature ºC and humidity %
RS485_0 1/2	RS485 [N]. Fuel level sensor with address N
llst0	Extended data RS232[0]. Depending on settings: 1. Temperature from fuel level sensors connected to RS232 0, °C 2. Weight, received from weight identifier
rs232_1	Expanded data RS232[1]. Depending on the settings: 1. Temperature from fuel level sensors connected to Rs232[1], °C 2. Weight received from weight identifier
llst1	Temperature from fuel level sensors connected to RS485 port with address 0, °C
llst2	Temperature from fuel level sensors connected to RS485 port with address 1, °C
llst3	Temperature from fuel level sensors connected to RS485 port with address 2, °C
Input8 /9/10/…/13	Input N value. Depending on the settings, one of the options is the following: 1. voltage, mV; 2. number of pulses; frequency, Hz.
Milliseconds
eco_acc	acceleration, units, 100 = 1g = 9,8 m/s2
eco_stop	breaking, units, 100 = 1g = 9,8 m/s2
eco_angl	cornering acceleration, 100 = 1g = 9,8 m/s2
eco_break	strike on bumps, 100 = 1g = 9,8 m/s2
TahoType	1 – SHTRIH-Taho RUS 2 – Atol Drive 5, Atol Drive Smart
TahoState	0 – not connected (did not try to connect after starting the terminal) 1 – not authorized (tried to log in but failed) 2 – authorized
TahoMode	not supported
TahoSpeed	Vehicle speed
TahoTrip	Trip distance
TahoIgnition	Ignition status
TahoMass
TahoFeryTrain
TahoActivity	0 – rest 1 – ready 2 – work 3 – driving
TahoCardType	card type: 1 – Driver card 5 – “Non-driver” card
TahoCardNumber	Driver card number
TahoActivity1
TahoActivity1
TahoActivityTime
TahoDrivingTime
TahoRestlessTime
TahoTahoVin	VIN code in ASCII
TahoVrn	Vehicle plate number